请选择 进入手机版 | 继续访问电脑版

气动避震论坛

 找回密码
 注册
搜索
热搜: 活动 交友 discuz
查看: 381|回复: 0

AIRBFT气动避震改装专用气管到货20000米温度-30--120摄氏度压力2.6mpa规格8*1mm

[复制链接]

3156

主题

3279

帖子

1万

积分

气动元老

Rank: 8Rank: 8

积分
11715
发表于 2020-12-13 14:01:55 | 显示全部楼层 |阅读模式

AIRBFT气动避震改装专用气管到货20000米温度-30--120摄氏度压力2.6mpa规格8*1mm
Airbft pneumatic shock absorber refitted special gas pipe arrives at 20000 m temperature - 30 -- 120 ℃, pressure 2.6MPa, specification 8 * 1mm


安装气动避震大致分为4个板块,也就是气动避震的安装,管路的铺设,线路的走位,和控制系统的安装!
下面就来一步步的分解一下:
先说气动避震的安装,气动避震桶身的安装其实是和更换普通的绞牙避震器是一样的,避震都是原车的安装位置,需要注意的就是根据避震的行程,计算出车主所需要的最高和最低的范围,来调节气动避震的高度,还有就是气管的预留位置,一般都是气管靠内侧走的,其他的就是照正常的避震安装步骤。
管路的铺设,管路的铺设是相当费时间的工作,每个安装师傅的手法和思路都是不一样的,但是要遵循一个原则就是一定要避开有可能折死弯或者是车辆行驶中可能压到或者是磨到气管的地方,还有就是离排气远一点,因为气管的材质多为趴高温的,最好的办法就是跟着油管一起走。
线路的走位,线路一般都是走车内的,跟着车内的电器线路一起,这是相当麻烦的,因为要拆装很多的内饰部件,最好是不要剪开主电源线,还有就是车内如果改有其他的用电设备的话一定不能共用电源线,防止互相干扰。
控制系统的安装,AIRBFT气动避震控制系统是相当简单的控制系统,但是想要完美的安装还是要有一定的经验的,应为有很多的细节都是需要注意的,尤其是各个接头和气管还有气孔的螺牙连接,都要用心安装,气孔和接头的螺牙连接一定要做好密封,应为如果有漏气情况,再来检查测试,是非常麻烦的,尽量一步到位。


The installation of pneumatic shock absorber is divided into four parts, that is, the installation of pneumatic shock absorber, the laying of pipelines, the travel of lines, and the installation of control system!
Let's break it down step by step
Let's talk about the installation of pneumatic shock absorber. The installation of pneumatic shock absorber barrel body is actually the same as that of replacing ordinary hinge suspension. Shock absorbers are all the installation positions of the original vehicle. It should be noted that the highest and lowest range required by the owner of the vehicle should be calculated according to the shock absorber travel, so as to adjust the height of the solar shock absorber, as well as the reserved position of the air pipe. Generally, the air pipe moves on the inner side The rest is to follow the normal shock absorber installation procedures.
The laying of pipelines and pipelines is a time-consuming work. The methods and ideas of each installation master are different. However, one principle should be followed, that is, to avoid the places that may be bent dead or where the vehicle may be pressed or ground to the air pipe, and that is, to keep away from the exhaust gas, because the material of the gas pipe is prone to high temperature, the best way is to It's going with the tubing.
When the line moves, the line usually goes in the car, along with the electrical circuit in the car, which is quite troublesome, because it is necessary to dismantle a lot of interior parts. It is better not to cut off the main power line. In addition, if there are other electrical equipment in the car, the power line must not be shared to prevent mutual interference.
For the installation of control system, airbft pneumatic shock absorber control system is a simple control system. However, if you want to perfect the installation, you need to have some experience, because there are many details that need to be paid attention to, especially the screw thread connection of each joint, air pipe and air hole, should be carefully installed. The screw tooth connection of air hole and joint must be well sealed, and if there is leakage Gas condition, and then check the test, is very troublesome, as far as possible one step in place.


f8c21ce93df025bae8aa53e94123539.png

5d619f89edee05f24951d0e36506465.png

8a990af4acdd814f80c1e1720dd33b9.png

353949a2a451e39baa4cee11dd7cf92.png

320ed1317ac6092bd2571b1ec533ad4.png

10704f74e585c1d2ebf693fa55a2472.png
公司名称:上海淞江减震器集团有限公司
英文名称:AIRBFT
公司地址:江苏省南通市双甸工业园区(淞江集团南通工厂)
公司网址:http://hellaflush-china.com 气动避震论坛
公司联系:13262966665
邮箱:981731567@QQ.com

Company name: Shanghai Songjiang shock absorber Group Co., Ltd
English Name: airbft
Address: Shuangdian Industrial Park, Nantong City, Jiangsu Province (Nantong factory of Songjiang group)
Company website: http://hellaflush-china.com Pneumatic shock absorber Forum
Company contact: 13262966665
Email: 981731567@QQ.com

微信:ACCU-AIR  关于安装或使用过程中出现的任何疑难杂症,ACCUAIR气动避震运营中心 李洋 为你答疑解惑 13262966665
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 注册

本版积分规则

论坛是网友自由讨论和发表个人见解的平台,所有涉及版权的著作(包括文字,图片,视频)等均属于网友个人行为, 与HellaFlush气动避震论坛,无任何利益关联。
版权所有:HellaFlush气动避震论坛如有任何问题,请点击此处。网站备案号:沪ICP备14006433号
快速回复 返回顶部 返回列表